Renewable
Country
Concrete underground structures
Use of thermal energy of the building plot for buildings whose concrete structure is built under the terrain.
This system allows geothermal activation of concrete foundation structures, underground walls, or Milan walls. Activated concrete structures serve as a geothermal absorber for supplying the building with heat and cold directly from their foundations.
The energy capacity of concrete underground structures basically depends on their volume.
Energokoše
Use of the thermal energy of the plot at a depth of 1-4 m below the surface of the terrain. Energokoše are a suitable solution for energy-independent houses located on smaller plots and are suitable for places where it is not possible to drill to greater depths.
The conical Energokoše are placed in the excavation and then covered back with soil. The energy cages are further connected to the energy processing equipment in the utility room of the house.
Thanks to the conical shape of Energokoše, the volume of land is used even in a relatively small area of the garden. The amount of Energokoš depends on the energy requirement.
Energoopilots
Use of thermal energy of building foundations of buildings that are built on base piles for static reasons.
This system allows geothermal activation of both prefabricated concrete foundation piles, drilling and worm piles, or pilots concreted directly on the construction site. Energopilots serve as a geothermal absorber for supplying heat and cold to buildings directly from their foundations.
The capacity of energopilots basically depends on the cross-section of the pilot reinforcement skeleton.
Geothermal borehole
Technology for the use of thermal energy of the plot at a depth from 100m and below its surface. Geothermal borehole does not lay claim to large plots of land and is a suitable solution for energy-independent houses.
Do vyvrtané štěrbiny v maximálním průměru 22cm jsou uložené geotermální sondy a následně jsou injektážní směsí teplovodivě spojeny se zemskou masou. Geotermální vrty jsou dále horizontálně propojeny se <em>zařízením pro zpracování energie</em> v technické místnosti domu.
Shallow Borehole - Vertical Thermpipe
Use of thermal energy of the plot at a depth of 6-12 m below its surface. Shallow geothermal borehole is a solution for energy-independent houses, where it is necessary to limit the depth of the well. It is suitable for places with the appearance of groundwater, and at the same time this technology does not lay claim to a large plot of land.
Vertical Thermpipe are 6m or 12m prefabricated elements that are installed in a drilled slot with a diameter of 26 or 36 cm. The shallow boreholes are further connected horizontally to the energy processing equipment in your machine room.
Surface collectors
Use of thermal energy of the plot at a depth of about 2 m below the surface of the terrain. Surface collectors are a suitable solution for energy-independent houses located on larger plots.
Horizontal distributions in 100 m lengths are placed in the trench and then they are then covered back with earth. The surface collectors are further connected to the energy processing equipment in the technical room of the house.
The efficiency of the system is influenced by the proportion of solar radiating energy. The size of the required area of the plot depends on the energy requirement.
Surface collectors under the base plate
Use of the thermal energy of the plot at a depth dependent on the excavation for the foundation slab of the building. Area collectors under the base plate are a suitable solution for energy-independent buildings where the built-up area is the same as the size of the building plot.
Horizontal pipelines in 100m lengths are laid in the trench and are subsequently covered with a standard foundation slab. The surface collectors are further connected to the energy processing equipment in the building's utility room.
The effectiveness of the system is influenced by the hydrogeological composition of the subsoil.
Use of PKS Thermpipe sewerage
Use of thermal energy of wastewater in sewer pipes under the surface of the terrain. PKS Thermpipe is a suitable solution for sewer networks not only of energy independent houses.
Wastewater has thermal potential and the PKS Thermpipe system is the logical and economical solution for its use. At the same time, heat is also obtained from the soil that surrounds the sewer pipes in the ground.
The PKS Thermpipe is further connected to the energy processing equipment in the utility room of the house.
The efficiency of the system is influenced by the location of the sewerage system, the temperature of the wastewater and the proportion of solar-emitting energy.
Concrete underground structures
Heat exchanger integrated into the construction concrete structures of buildings, in the part where there is a concrete structure under the terrain.
This system allows geothermal activation of concrete foundation structures, underground walls, or Milan walls. Activated concrete structures serve as a geothermal absorber for supplying the building with heat and cold directly from their foundations.
The energy capacity of concrete underground structures basically depends on their volume.
– Suitable for low-temperature heating and cooling of buildings.
Energokoše
Heat exchanger for the use of the energy of the plot at a depth of 1-4 m below the surface of the terrain. Energokoše are a suitable solution for energy-independent houses located on smaller plots and are suitable for places where it is not possible to drill to greater depths.
– Basket diameter 2.4m/1.4m, height 2-2.7m, storage directly in the ground.
– Two types of basket sizes (150/200m pipe 32×2.9mm)
– The efficiency of Energokoš is influenced by the proportion of solar emitting energy and soil moisture.
– Suitable for low-temperature heating and cooling of buildings.
– Without the need for geological surveys or permits.
Energoopilots
Heat exchanger integrated into the building foundations of buildings that are built on base piles for static reasons.
This system allows geothermal activation of both prefabricated concrete foundation piles, drilling and worm piles, or pilots concreted directly on the construction site. Energopilots serve as a geothermal absorber for supplying heat and cold to buildings directly from their foundations.
The capacity of energopilots basically depends on the cross-section of the pilot reinforcement skeleton.
– Suitable for low-temperature heating and cooling of buildings.
Geothermal borehole
Heat exchanger for the use of the energy of the plot at a depth from 100m and below its surface. Extensive land is not required for installation and is a suitable solution for energy-independent houses.
– Constant temperature from 15m below ground and geothermal gradient 3°C/100m.
– Bore diameter 150-220mm, borehole depth in the range of 80-400m.
– Borehole spacing ideally 10m.
– The efficiency of the borehole is influenced by the geological subsoil and the quality of the injection mixture and the overall design.
– Suitable for low-temperature heating and cooling of buildings.
– The need for geological surveys, and a report or a mining permit.
– Geothermal borehole power ranges from 10 to 70 W/m, but can also reach 100 W/m.
Shallow Borehole - Vertical Thermpipe
Prefabricated heat exchanger for the use of the energy of the plot at a depth of 6-12 m below its surface. Extensive land is not required for installation and is a suitable solution for energy-independent houses, when it is necessary to limit the depth of the well. Functionality depends on the occurrence of groundwater.
– Ideal installation using a hollow worm drill.
– Diameter 260/360 mm, borehole depth 6/12m (other on request)
– Prefabricates have a pressure test with a certificate.
– The efficiency of the well is influenced by geological subsoil and the occurrence of groundwater.
– Suitable for low-temperature heating and cooling of buildings.
– The need for geological survey and report.
Surface collectors
Heat exchanger for the use of land energy at a depth of about 2 m below the surface of the terrain. Surface collectors are a suitable solution for energy-independent houses located on larger plots.
– Diameter of special PE RC pipe d32-110, storage directly into the ground.
– The efficiency of collectors is influenced by the proportion of solar radiating energy and soil moisture.
– Suitable for low-temperature heating and cooling of buildings.
– Without the need for geological surveys, and a report or permit.
Surface collectors under the base plate
Heat exchanger for the use of the thermal energy of the plot at a depth below the building base plate. Area collectors under the foundation plate are a suitable solution for energy independent houses where the built-up area is the same as the size of the building plot.
– Diameter of special PE RC pipe d32-110, storage directly into the ground.
– Performance depends on the dimensions of the built-up area.
– Suitable for low-temperature heating and cooling of buildings.
– Without the need for geological surveys, and a report or permit.
Use of PKS Thermpipe sewerage
Use of thermal energy of wastewater in sewer pipes under the surface of the terrain. PKS Thermpipe is a suitable solution for sewer networks not only of energy independent houses.
Wastewater has thermal potential and the PKS Thermpipe system is the logical and economical solution for its use. At the same time, heat is also obtained from the soil that surrounds the sewer pipes in the ground.
The PKS Thermpipe is further connected to the energy processing equipment in the utility room of the house.
The efficiency of the system is influenced by the location of the sewerage system, the temperature of the wastewater and the proportion of solar-emitting energy.
Concrete underground structures
Use of thermal energy of your building plot for buildings whose concrete structure is built under the ground.
This system allows geothermal activation of concrete foundation structures, underground walls, or Milan walls. Activated concrete structures serve as a geothermal absorber for supplying the building with heat and cold directly from their foundations.
The advantage is lower input costs than for separate geothermal wells.
Energokoše
Use of the thermal energy of your plot at a depth of 1-4 m below the surface of the terrain. Energokoše are suitable for smaller plots and places where it is not possible to drill to greater depths.
Thanks to the conical shape of Energokoše, the volume of land is used even in a relatively small area of the garden. The advantage is easy installation without costly drilling.
The conical Energokoše are placed in the excavation and then covered back with soil. The energy cubes are further connected to the energy processing equipment in the mechanical room of your house.
The amount of Energokoš depends on the energy requirement. Installation is not subject to special permission.
Energoopilots
Use of thermal energy of your building site under the surface of the terrain for buildings that are built on base piles for static reasons.
This system allows geothermal activation of both prefabricated concrete foundation piles, drilling and worm piles, or pilots concreted directly on the construction site. Energopilots serve as a geothermal absorber for supplying heat and cold to buildings directly from their foundations.
The advantage is lower input costs than for separate geothermal wells.
Geothermal borehole
Use of the thermal energy of your plot at a depth of 100m and below its surface. Geothermal borehole has the advantage of an almost constant heat source, and at the same time this technology does not lay claim to a large plot of land. The number and depth of wells depends on the energy requirement of the house.
Do vyvrtané štěrbiny v maximálním průměru 22cm jsou uložené geotermální sondy a následně jsou injektážní směsí teplovodivě spojeny se zemskou masou. Geotermální vrty jsou dále propojeny se <em>zařízením pro zpracování energie</em> ve vaší strojovně.
Drilling is subject to a report to the competent authority. When drilling to greater depths, a high-level permit is required.
Shallow Borehole - Vertical Thermpipe
Use of the thermal energy of your plot at a depth of 6-12 m below its surface. Shallow geothermal borehole is the solution for situations where it is necessary to limit the depth of the well. It is suitable for places with the appearance of groundwater, and at the same time this technology does not lay claim to a large plot of land. The number of wells depends on the energy requirement of the house.
Vertical Thermpipe are 6m or 12m prefabricated elements that are installed in a drilled slot with a diameter of 26 or 36 cm. The shallow boreholes are further connected to the energy processing equipment in your machine room. Drilling is subject to notification to the relevant authority.
Surface collectors
Use of thermal energy of your plot at a depth of about 2 m below the surface of the terrain. Surface collectors are suitable for larger plots, it is possible to install it yourself and significantly reduce input costs. Surface collectors have a relatively high seasonal performance factor.
Horizontal distributions in 100 m lengths are placed in the trench and then they are then covered back with earth. The surface collectors are further connected to the energy processing equipment in the engine room of your house.
The length of the distribution depends on the energy requirement. Installation is not subject to notification or permission.
Surface collectors under the base plate
Use of the thermal energy of your property at a depth below the foundation plate of the building. The area collectors under the base plate are suitable for buildings where the built-up area is the same as the size of the building plot.
Horizontal pipelines in 100m lengths are laid in the trench and are subsequently covered with a standard foundation slab. The surface collectors are further connected to the energy processing equipment in your building's mechanical room.
The length of the wiring depends on the dimensions of the built-up area and the energy requirement of the building.
Use of PKS Thermpipe sewerage
Use of thermal energy of wastewater in sewer pipes under the surface of the terrain. PKS Thermpipe is a suitable solution for sewer networks not only of energy independent houses.
Wastewater has thermal potential and the PKS Thermpipe system is the logical and economical solution for its use. At the same time, heat is also obtained from the soil that surrounds the sewer pipes in the ground.
The PKS Thermpipe is further connected to the energy processing equipment in the utility room of the house.
The efficiency of the system is influenced by the location of the sewerage system, the temperature of the wastewater and the proportion of solar-emitting energy.
Air
Outdoor air unit
This unit allows you to draw thermal energy from the air that is always around us. If possible, this unit can be located on the roof, façade, or on the grounds of the building.
The advantage of this unit is high efficiency, quiet operation with patented defrosting technology, which increases the coefficient of seasonal performance.
The compact design of the unit and its aurding design are complemented by a fan with high efficiency and controlled speed. Guaranteed system functionality in temperatures up to -15°C.
The outdoor air unit is further connected to the hydrobox in the technical room of the building.
Outdoor air unit
This unit allows you to draw thermal energy from the air that is always around us. If possible, this unit can be located on the roof, façade, or on the grounds of the building.
The advantage of this unit is high efficiency, quiet operation with patented defrosting technology, which increases the coefficient of seasonal performance.
Venkovní vzduchová jednotka je dále propojena s <em>tepelným čerpadlem</em> v technické místnosti budovy.
– Hydraulic connection without refrigerant.
– System functionality at temperatures up to -15°C.
– Ziehl-Abegg axial fan with high performance and quiet operation
- Fan speed control system
– Built-in system for hybrid use of the unit
– Patented defrosting technology
– Possibility of connecting multiple units to the jump
Outdoor air unit
This unit allows you to draw thermal energy from the air that is always around us. If possible, this unit can be located on the roof, façade, or on the grounds of the building.
Thanks to our experience in developing innovative technologies, our outdoor unit boasts very quiet operation, high efficiency and a fan with controlled speed.
The compact design of the unit and its sparing design are complemented by patented defrosting technology. This is manifested by increased seasonal performance.
It also includes protection for operation in extreme weather conditions. This is also demonstrated by the guaranteed functionality of the system at temperatures of -15°C.
Venkovní vzduchová jednotka je dále propojena s <em>tepelným čerpadlem</em> v technické místnosti vaší budovy.
Water
Lima
Use of thermal energy from ponds, lakes and rivers near the building. Lima is a special system for receiving energy from surface water and is a suitable solution for energy-independent houses located around water sources.
Compact design and installation under the water surface creates a visually undisturbed environment around the house. For the required higher performance, the possibility of connecting several units of the Lima system in series.
Lima is further connected to the energy processing equipment in the utility room of the house.
Groundwater
Use of thermal energy of groundwater under the surface of the plot. This system for receiving energy from groundwater and is a suitable solution for energy-independent houses located on land that is rich in groundwater.
This system for receiving thermal energy works on the principle of pumping groundwater from one well to another.
In the excavated boreholes of wider diameters are inserted logs, equipped with filter packing and sealing in the upper part. A submersible pump is located in the first well, which injects the water into the energy processing equipment in the utility room of the house. There, the thermal energy is used and the water is pumped back into the ground via the second well.
Hydrothermal submarine
The development of an innovative modular heat exchanger is created in cooperation with the Technical University of Darmstadt at the Department of Hydraulic Engineering and Hydraulics. The new system allows the use of the thermal potential of water and at the same time its kinetic energy during flow (e.g. rivers). The research is funded by the 'Central Innovation Programme for SMEs'.
Lima
Heat exchanger for energy utilization of surface water sources in the vicinity of the realization. The Lima system is a suitable solution for energy-independent houses located around ponds, rivers or lakes.
For the required higher performance, the possibility of connecting several Units of the Lima system into the series.
– Installation by immersion in surface water.
– Temperature range -10°C to +40°C.
– Suitable for low-temperature heating and cooling of buildings.
– Installation is subject to approval by the administrator of a specific water source.
– Compact dimensions 1070x1120mm
Groundwater
Heat exchanger for the use of energy of underground water sources under the terrain of the plot. The system is a suitable solution for energy-independent houses located on plots that are rich in the appearance of groundwater.
For the required higher performance, the possibility of connecting several Units of the Lima system into the series.
– Principle of groundwater pumping in two wells.
– Groundwater temperature is constant year-round 7-12°C.
– Suitable for low-temperature heating and cooling of buildings.
– Installation is subject to approval by the administrator of a specific water source.
Hydrothermal submarine
The development of an innovative modular heat exchanger is created in cooperation with the Technical University of Darmstadt at the Department of Hydraulic Engineering and Hydraulics. The new system allows the use of the thermal potential of water and at the same time its kinetic energy during flow (e.g. rivers). The research is funded by the 'Central Innovation Programme for SMEs'.
Lima
The use of thermal energy from ponds, lakes and rivers near your house. Lima is a special system for receiving energy from surface waters. The compact design is ideal for quick and easy installation.
Lima is made of long-lasting eco-plastic. Materials specially developed for fast heat transfer are used for the components. Lima is also connected to the energy processing equipment in the mechanical room of your house.
For the required higher performance, the possibility of connecting several units of the Lima system in series. The installation is subject to approval by the administrator of a particular water source.
Groundwater
The use of thermal energy from groundwater beneath the surface of your property. This system for receiving thermal energy works on the principle of pumping groundwater from one well to another.
In the excavated boreholes of wider diameters are inserted logs, equipped with filter packing and sealing in the upper part. A submersible pump is located in the first well to inject water into the energy processing plant. There, the thermal energy is used and the water is pumped back into the ground through the second well.
The system for pumping geothermal energy from water achieves the highest heating effects. The system is suitable for places where there is enough groundwater. This system is not maintenance-free compared to others.
Installation is subject to permission by the administrator of a particular water source.
Hydrothermal submarine
The development of an innovative modular heat exchanger is created in cooperation with the Technical University of Darmstadt at the Department of Hydraulic Engineering and Hydraulics. The new system allows the use of the thermal potential of water and at the same time its kinetic energy during flow (e.g. rivers). The research is funded by the 'Central Innovation Programme for SMEs'.
Hybrid
Hybrid system
This system allows you to cleverly draw thermal energy from air, earth or water depending on seasonal conditions and current energy efficiency.
Thus, a choice of several principles of energy pumping is possible. For example, it is possible to combine Geothermal boreholes with an Outdoor Air Unit. The advantage is the economic use of geothermal and aerothermal energy in different seasons.
The hybrid system gives you the opportunity to reduce the number of geothermal wells or their depth. Also, in case of lack of space on the plot for a surface collector, the air unit can serve as a power reserve.
A plus of this system is also the more efficient regeneration of the earth's subsoil. In summer, excess thermal energy is passed back to the country from which it was pumped in the winter months.
These systems are connected to a hybrid heat pump in the technical room of the building.
Hybrid system
This system allows you to cleverly draw thermal energy from air, earth or water depending on seasonal conditions and current energy efficiency.
Thus, a choice of several principles of energy pumping is possible. For example, it is possible to combine Geothermal boreholes with an Outdoor Air Unit. The advantage is the economic use of geothermal and aerothermal energy in different seasons.
The hybrid system gives you the opportunity to reduce the number of geothermal wells or their depth. Also, in case of lack of space on the plot for a surface collector, the air unit can serve as a power reserve.
A plus of this system is also the more efficient regeneration of the earth's subsoil. In summer, excess thermal energy is passed back to the country from which it was pumped in the winter months.
These systems are connected to a hybrid heat pump in the technical room of the building.
Hybrid system
This system allows you to cleverly draw thermal energy from air, earth or water depending on seasonal conditions and current energy efficiency.
Thus, a choice of several principles of energy pumping is possible. For example, it is possible to combine Geothermal boreholes with an Outdoor Air Unit. The advantage is the economic use of geothermal and aerothermal energy in different seasons.
The hybrid system gives you the opportunity to reduce the number of geothermal wells or their depth. Also, in case of lack of space on the plot for a surface collector, the air unit can serve as a power reserve.
A plus of this system is also the more efficient regeneration of the earth's subsoil. In summer, excess thermal energy is passed back to the country from which it was pumped in the winter months.
These systems are connected to a hybrid heat pump in the technical room of the building.
sun
E - Manager
This system is part of a revolutionary smart grid that uses digital communication technology.
The E-Manager detects excess electricity generated from photovoltaic panels and regulates the heat pump to an optimal balance between consumption and production. When the power generation from photovoltaic panels decreases, the E-Manager returns the heat pump to standard operation.
E-Manager allows you to set the consumption schedule depending on the prices of electricity during peak hours, and at the same time depending on the season. The heat pump will produce more heat energy at a time when electricity from the grid is cheaper and thus saves our finances.
It is possible to set the power limit of the heat pump. If the consumption level is close to the set limit, the E-Manager reduces the electricity consumption so as not to exceed the limit.
E-System
This system is part of a revolutionary smart grid that uses digital communication technology.
The E-System extends the E-Manager with an inverter and built-in storage batteries. When there is an excess of electricity from photovoltaic panels, the E-System stores the generated electricity in batteries. In the event of a decrease in its own power generation, the heat pump is driven by stored energy. The built-in inverter also has an optional EPS (Safe Power Mode) function, which allows you to use the stored energy in the event of a power outage from the mains. The E-System is maintenance-free and its batteries with an intelligent charging system have a lifespan of 10 years.
Thanks to its modularity, the E-System is customizable and can be sized according to performance requirements. The storage capacity ranges from 2.4 to 12 kWh.
Hybrid photovoltaic panels
Hybrid photovoltaic panels have a specially developed system of copper tubular meanders. Compared to standard photovoltaic panels, they excel in higher electricity production.
Hybrid photovoltaic cells are cooled and the panels do not overheat. Depending on the conditions, the obtained thermal energy from the panels can be used and thus reduce the economic burden on the operation of the house.
The use of the energy potential of hybrid photovoltaic panels is similar to that of solar collectors (e.g. for preheating hot water, direct heating of hot water and other technological principles).
E - Manager
This system is part of a revolutionary smart grid that uses digital communication technology.
The E-Manager detects excess electricity generated from photovoltaic panels and regulates the heat pump to an optimal balance between consumption and production. When the power generation from photovoltaic panels decreases, the E-Manager returns the heat pump to standard operation.
E-Manager allows you to set the consumption schedule depending on the prices of electricity during peak hours, and at the same time depending on the season. The heat pump will produce more heat energy at a time when electricity from the grid is cheaper and thus saves our finances.
It is possible to set the power limit of the heat pump. If the consumption level is close to the set limit, the E-Manager reduces the electricity consumption so as not to exceed the limit.
E-System
This system is part of a revolutionary smart grid that uses digital communication technology.
The E-System extends the E-Manager with an inverter and built-in storage batteries. When there is an excess of electricity from photovoltaic panels, the E-System stores the generated electricity in batteries. In the event of a decrease in its own power generation, the heat pump is driven by stored energy. The built-in inverter also has an optional EPS (Safe Power Mode) function, which allows you to use the stored energy in the event of a power outage from the mains. The E-System is maintenance-free and its batteries with an intelligent charging system have a lifespan of 10 years.
Thanks to its modularity, the E-System is customizable and can be dimensioned according to performance requirements. The accumulation capacity is in the range from 2.4 to 9.6 kWh.
Hybrid photovoltaic panels
Hybrid photovoltaic panels have a specially developed system of copper tubular meanders. Compared to standard photovoltaic panels, they excel in higher electricity production.
Hybrid photovoltaic cells are cooled and the panels do not overheat. Depending on the conditions, the obtained thermal energy from the panels can be used and thus reduce the economic burden on the operation of the house.
The use of the energy potential of hybrid photovoltaic panels is similar to that of solar collectors (e.g. for preheating hot water, direct heating of hot water and other technological principles).
E - Manager
This system is part of a revolutionary smart grid that uses digital communication technology.
The E-Manager detects excess electricity generated from photovoltaic panels and regulates the heat pump to an optimal balance between consumption and production. When the power generation from photovoltaic panels decreases, the E-Manager returns the heat pump to standard operation.
E-Manager allows you to set the consumption schedule depending on the prices of electricity during peak hours, and at the same time depending on the season. The heat pump will produce more heat energy at a time when electricity from the grid is cheaper and thus saves our finances.
It is possible to set the power limit of the heat pump. If the consumption level is close to the set limit, the E-Manager reduces the electricity consumption so as not to exceed the limit.
E-System
This system is part of a revolutionary smart grid that uses digital communication technology.
The E-System extends the E-Manager with an inverter and built-in storage batteries. When there is an excess of electricity from photovoltaic panels, the E-System stores the generated electricity in batteries. In the event of a decrease in its own power generation, the heat pump is driven by stored energy. The built-in inverter also has an optional EPS (Safe Power Mode) function, which allows you to use the stored energy in the event of a power outage from the mains. The E-System is maintenance-free and its batteries with an intelligent charging system have a lifespan of 10 years.
Thanks to its modularity, the E-System is customizable and can be dimensioned according to performance requirements. The accumulation capacity is in the range from 2.4 to 9.6 kWh.
Hybrid photovoltaic panels
Hybrid photovoltaic panels have a specially developed system of copper tubular meanders. Compared to standard photovoltaic panels, they excel in higher electricity production.
Hybrid photovoltaic cells are cooled and the panels do not overheat. Depending on the conditions, the obtained thermal energy from the panels can be used and thus reduce the economic burden on the operation of the house.
The use of the energy potential of hybrid photovoltaic panels is similar to that of solar collectors (e.g. for preheating hot water, direct heating of hot water and other technological principles).