End elements

A system for the integration of air conditioning in the concrete skeleton of buildings.

Batiso Air is a system that allows you to integrate air distribution systems in ceiling concrete structures. The air supply is distributed in this way to the air outlets integrated in the floor. The technology allows the distribution of fresh air into rooms without a ceiling.

The advantage is interiors without suspended ceilings, optimal air distribution in the building, hygienic safety in combination with high thermal comfort.

Designed for new multi-storey buildings with a reinforced concrete skeleton. Ideal to combine with Batiso(TABS) technology.

A system for radiant heating and cooling of buildings, which uses the accumulation capabilities of the concrete core.

Batiso are PEX tubular registers located in the center of the neutral zone of the reinforced concrete skeleton of the house.  Based on the requirements, circulatory systems up to 25kPa pressure drop are defined.

Batiso can be built in both horizontal and vertical directions. The skeleton of the house then radiates the accumulated energy into the living spaces. The effect in space comes with a temporal response and is dependent on the state of accumulation and the current temperature in the space. The delay can be shortened by a special design.

Individual temperature control in the rooms is only possible through an additional recirculation system.

The advantage is its maintenance-free system, relatively low investment and invisibility in the interior combined with high thermal comfort.

Designed for new multi-storey buildings with reinforced concrete skeleton and interiors with exposed shackled concrete. Ideal to combine with geothermal energy sources.

Low-temperature system for radiant ceiling heating and cooling of spaces. Carbon S plates with built-in copper topně-cooling device form the ceiling area. It is possible to create seamless full-surface or island surfaces.

The design of the system is adapted to the design of dry construction. The system is not primarily designed for rooms with difficult spatial geometry or with requirements for embedded technologies.

As part of the design, it is necessary to combine the active parts of the ceiling (Carbon S boards) with the inactive part (gypsum-cardboard boards).

The advantage is an affordable solution combined with high performance. Suitable for use with geothermal energy sources.

– High-performance system

– The medium for heating and cooling is water.

- 6 standard dimensions

– Ground clearance 15mm

– Power for cooling 100W/^m2 ∆^t 8K / heating 145W/^m2 ∆^t 15K (according to EN 140 37)

Low-temperature system for radiant ceiling heating and cooling of spaces. The Reno system is a drywall of standard dimensions, in which there is a built-in pipe for the distribution of cold and heat.

It is possible to create seamless full-surface or island surfaces. Reno is especially suitable for renovations.

The design of the Reno system is adapted to the construction of dry construction, but not to the built-in installation of other technologies in space and difficult spatial geometry.

The material of the system gypsum-cardboard plate is reinforced with glass fiber.

– SDK ceiling system

– The medium for heating and cooling is water

– Built-in pipe size 9.9 x 1.1 mm

– Plate thickness 15mm

– Power for cooling 47 W/^m2 ∆^t 10K / heating 55 W/^m2 ∆^t 15K (According to EN 140 37)

Unique low-temperature system for radiant ceiling heating and cooling of the premises. The UNI system is part of the supporting structure of the plasterboard ceiling. It is possible to create seamless full-surface or island surfaces.

The design of the system is adapted to the design of dry construction, the installation of additional technologies in space and difficult spatial geometry.

The cover for the UNI system are special gypsum-cardboard plates with increased thermal conductivity. By using perforated plates with a layer of acoustic fabric, acoustically efficient execution can be achieved.

– System for SDK ceiling

– The medium for heating and cooling is water.

– Ground clearance of the system 70mm

– Acoustics α _W = 0.6 (according to EN ISO 11654)

– Power for cooling 50-80W/^m2 ∆^t 10K / heating 63-92W/^m2 ∆^t 15K (according to EN 140 37)

System for radiant ceiling heating and cooling. Comfortable draught-free solution for heating buildings. Wood is a natural gypsum fiber panel with a final surface of wood veneer. The panels are fixed under the ceiling in a regular grid and create full-surface seamless ceiling soffits.

The appearance can be individualized in a wide range of woody decors. The advantage is its
exclusive design combined with excellent acoustic properties.

In areas with the Wood system, no additional radiators or cooling elements are required. Wood system panels are produced in several dimensions.
Built-in ceiling components (lighting, audio speakers, shading technology...).

Cooling capacity 56W/^m2 ∆^t 8K (According to EN 140 37)

Sound absorption αW = up to 0,45 (EN ISO 11654)

A unique system for radiant ceiling heating and cooling of the premises. Radiant heating is the most effective way to create a comfortable and pleasant environment in any home.

The UNI system is part of the load-bearing structure of the plasterboard ceiling and can be used to create seamless full-surface or island ceiling soffits.

The advantage is its invisibility in the interior, functionality without any noise and the principle of heat radiation, which is pleasant for the body. In rooms with the UNI system, no additional radiators or cooling elements are required.

Thanks to the fact that we design the UNI system tailored to a specific room, there is no problem with the installation of built-in ceiling components (lighting, audio speakers, shading technology...).

We combine the UNI system with special drywall with increased thermal conductivity and the possibility of noise absorption.

Power for cooling 50-80W/^m2 ∆^t 10K / heating 63-92W/^m2 ∆^t 15K (According to EN 140 37)

System for radiant ceiling heating and cooling. Comfortable draught-free solution for heating buildings. Wood is a natural gypsum fiber panel with a final surface of wood veneer. The panels are fixed under the ceiling in a regular grid and create full-surface seamless ceiling soffits.

The appearance can be individualized in a wide range of woody decors. The advantage is its
exclusive design combined with excellent acoustic properties.

In areas with the Wood system, no additional radiators or cooling elements are required. Wood system panels are produced in several dimensions.
Built-in ceiling components (lighting, audio speakers, shading technology...).

Cooling capacity 56W/^m2 ∆^t 8K (According to EN 140 37)

Sound absorption αW = up to 0,45 (EN ISO 11654)

System for radiant ceiling heating and cooling of spaces. Comfortable draught-free solution and attractive interior appearance.

The Carbon S ceiling system consists of a standard suspended supporting structure and carbon plates with integrated topně-cooling equipment. It can be used to create seamless full-surface or island ceiling soffits.

The advantage is its invisibility in the interior in combination with high performance. In areas with the Carbon S system, no additional radiators or cooling elements are required.

Power for cooling 100W/^m2 ∆^t 8K / heating 145W/^m2 ∆^t 15K (according to EN 140 37)

System for radiant ceiling heating and cooling of spaces. Radiant heating is the most effective way to create a comfortable and pleasant environment in any home.

Reno is a drywall of standard dimensions, in which there is a built-in pipe for the distribution of cold and heat. Reno is designed for a dry construction system with quick assembly suitable especially for renovations.

The installation of the Reno system is similar to that of a standard plasterboard ceiling. However, the boards can not be cut as needed, but it is necessary to make plans for laying in advance. With the Reno system, seamless full-surface or island ceiling soffits can be created.

The advantage is its ease of installation and invisibility in the interior. Because the Reno system is universal, it is not possible to install built-in ceiling components (lighting, audio speakers, shading technology...).

Power for cooling 47 W/^m2 ∆^t 10K / heating 55 W/^m2 ∆^t 15K (According to EN 140 37)

A system for radiant heating and cooling of buildings that uses the accumulation capacity of concrete.

Batiso is a technology placed in the reinforced concrete skeleton of the house in which a tempered topně-cooling medium circulates. It can be placed in ceilings, floors and walls. The skeleton of the house accumulates heat or cold and, with a time delay, radiates it into the living quarters.

The advantage is its maintenance-free system, relatively low investment and invisibility in the interior combined with high thermal comfort.

Designed for new multi-storey buildings with reinforced concrete skeleton and interiors with exposed shackled concrete. Ideal to combine with geothermal sources of thermal energy.

A system for the integration of air conditioning in the concrete skeleton of buildings.

Batiso Air is a system that allows you to integrate air distribution systems in ceiling concrete structures. The air supply is distributed in this way to the air outlets integrated in the floor. The technology allows the distribution of fresh air into rooms without a ceiling.

The advantage is interiors without suspended ceilings, optimal air distribution in the building, hygienic safety in combination with high thermal comfort.

Designed for new multi-storey buildings with a reinforced concrete skeleton. Ideal to combine with Batiso(TABS) technology.

System for radiant wall heating and cooling of spaces. The Reno S system is a drywall of standard dimensions, in which there is a built-in pipe for the distribution of cold and heat.

Seamless surfaces can be created. The Reno S is particularly suitable for renovations.

The design of the Reno S system is adapted to the construction of dry construction, but not to anchor furniture and accessories in the interior and difficult spatial geometry. Places for anchoring must be determined already in the project phase, and replace the Reno S board with a conventional gypsum-cardboard one.

The material of the system gypsum-cardboard plate is reinforced with glass fiber.

– SDK wall system

– The medium for heating and cooling is water

– Built-in pipe dimensions 9.9 x 1.1 mm
– Plate thickness 15mm

Power for cooling 41 W/^m2 ∆^t 10K / heating 62 W/^m2 ∆^t 15K (According to EN 140 37)

System for radiant wall heating and cooling of spaces. The Tenno system consists of an integrated topně-cooling register into the construction of plasterboard walls.

Tenno is designed for a dry construction system and can be used to create seamless wall surfaces.

The advantage is its invisibility in the interior, functionality without any noise.

Thanks to the fact that we design the Tenno system tailored to a specific room, it is planned in advance with additional requirements for the installation of additional technologies.

We combine the Tenno system with special drywall with increased thermal conductivity.

– SDK wall system

– The medium for heating and cooling is water
– Construction depth 42 mm

– Cooling capacity 56W/^m2 ∆^t 10K / heating 82 W/^m2 ∆^t 15K (According to EN 140 37)

System for wall-mounted space heating and cooling. Radiant heating is the most effective way to create a comfortable and pleasant environment in the interior.

Reno S is a drywall of standard dimensions, in which there is a built-in pipe for the distribution of cold and heat. Reno S is designed for a dry construction system with quick assembly suitable especially for renovations.

The installation of the Reno S system is similar to the construction of standard plasterboard partitions. However, the boards cannot be shortened as needed, but it is necessary to create laying plans in advance.

The advantage is its ease of installation and invisibility in the interior. However, because the Reno S system is universal, it is not possible to install TV mounts, paintings, screens, shelves, lighting, etc. in it. These places must be identified already in the project phase, and replace the Reno S board with a conventional gypsum-cardboard one.

Power for cooling 41 W/^m2 ∆^t 10K / heating 62 W/^m2 ∆^t 15K (According to EN 140 37)

System for wall-mounted space heating and cooling. Radiant heating is the most effective way to create a comfortable and pleasant environment in the interior.

The Tenno system is integrated into the construction of plasterboard walls and can be used to create seamless wall surfaces. Tenno is designed for dry construction system.

The advantage is its invisibility in the interior, functionality without any noise and the principle of heat radiation, which is pleasant for the body. In rooms with the Tenno system, no additional radiators or cooling elements are required.

Thanks to the fact that we design the Tenno system tailored to a specific room, it is planned in advance with the installed components (TV holders, paintings, screens, shelves, lighting, etc.).

We combine the Tenno system with special drywall with increased thermal conductivity.

Power for cooling 56W/^m2 ∆^t 10K / heating 82 W/^m2 ∆^t 15K (According to EN 140 37)

When showering, wastewater is generated around 33 ° C, which we discharge into the sewer. Waste water heat exchanger – SmartShower extracts heat from the waste water and preheats the incoming cold water for showering.

The heat exchanger, which is installed under the shower tray, absorbs thermal energy from the waste water and dissipates the heat into the cold drinking water and preheats it to a temperature of approx. 20°C.

Because preheated water is mixed with warm water, less energy-efficient hot water is needed to reach the desired temperature in the shower. In case you want to take a cold shower, the heat exchanger will not affect the temperature in the shower.

Possibility to connect two exchangers in series to one shower. The annual saving on such an installation is 30-40%..

When showering, wastewater is generated around 33 ° C, which we discharge into the sewer. Waste water heat exchanger – SmartShower extracts heat from the waste water and preheats the incoming cold water for showering.

The heat exchanger, which is installed under the shower tray, absorbs thermal energy from the waste water and dissipates the heat into the cold drinking water and preheats it to a temperature of approx. 20°C.

Because preheated water is mixed with warm water, less energy-efficient hot water is needed to reach the desired temperature in the shower. In case you want to take a cold shower, the heat exchanger will not affect the temperature in the shower.

Possibility to connect two exchangers in series to one shower. The annual saving on such an installation is 30-40%..

We offer underfloor heating systems for both new and reconstructed buildings.

Thanks to invisible installations, there is no need to install radiators and unsightly pipes in the room. The slight radiant heat produced by the underfloor heating system heats the air in the room.

With underfloor heating technology, every square centimeter in the room can be thermally activated. However, this advantage applies only in cases where furniture is not placed on the floor. Cabinets, chests of drawers, sofas, kitchen cabinets are large and detract from the necessary power for thermal comfort.

One of the most economical ways to supply energy to underfloor heating is to use one of our primary energy sources. All radiant heating and cooling solutions operate as low-temperature solutions and therefore consume less energy than most other solutions.

In our offer there are floor systems in the thickness range from 14mm, which are ideal for reconstructions.

We offer underfloor heating systems for both new and reconstructed buildings.

Thanks to invisible installations, there is no need to install radiators and unsightly pipes in the room. The slight radiant heat produced by the underfloor heating system heats the air in the room.

With underfloor heating technology, every square centimeter in the room can be thermally activated. However, this advantage applies only in cases where furniture is not placed on the floor. Cabinets, chests of drawers, sofas, kitchen cabinets are large and detract from the necessary power for thermal comfort.

One of the most economical ways to supply energy to underfloor heating is to use one of our primary energy sources. All radiant heating and cooling solutions operate as low-temperature solutions and therefore consume less energy than most other solutions.

In our offer there are floor systems in the thickness range from 14mm, which are ideal for reconstructions.